Welcome to one of the most active flamenco sites on the Internet. Guests can read most posts but if you want to participate click here to register.
This site is dedicated to the memory of Paco de Lucía, Ron Mitchell, Guy Williams, Linda Elvira, Philip John Lee, Craig Eros, Ben Woods, David Serva and Tom Blackshear who went ahead of us.
We receive 12,200 visitors a month from 200 countries and 1.7 million page impressions a year. To advertise on this site please contact us.
|
|
Building two under influence of a 1973 Sobrinos de Esteso
|
You are logged in as Guest
|
Users viewing this topic: none
|
|
Login | |
|
ernandez R
Posts: 747
Joined: Mar. 25 2019
From: Alaska USA
|
RE: Building two under influence of ... (in reply to estebanana)
|
|
|
Steven, The tried the end grain plugs once, hickory, but my taper ream just shredded the grain rather then cutting it. The ream was mostly new but not the best quality, smooth on one side and three cutting edges on the other. Perhaps a spiral cut ream would perform better? The hickory I used is, well it’s hickory and hard as a baseball bat or hammer handle. I’ve taken to just case hardening then bore with thin CA, letting it cure for 24 hours and then reaming again. I’ve also been doing the same with my wooden pegs only two or three layers scraping after each application. With care I’ve been able to make the bore and pins exact enough to be interchangeable. I start by making my pins 1/4” on the small end and all other dimensions fallow. Looking forward to the rest of your build. HR
_____________________________
I prefer my flamenco guitar spicy, doesn't have to be fast, should have some meat on the bones, can be raw or well done, as long as it doesn't sound like it's turning green on an elevator floor. www.instagram.com/threeriversguitars
|
|
|
REPORT THIS POST AS INAPPROPRIATE |
Date Sep. 9 2020 18:12:59
|
|
estebanana
Posts: 9379
Joined: Oct. 16 2009
|
RE: Building two under influence of ... (in reply to ernandez R)
|
|
|
quote:
teven, The tried the end grain plugs once, hickory, but my taper ream just shredded the grain rather then cutting it. The ream was mostly new but not the best quality, smooth on one side and three cutting edges on the other. Perhaps a spiral cut ream would perform better? The hickory I used is, well it’s hickory and hard as a baseball bat or hammer handle. I’ve taken to just case hardening then bore with thin CA, letting it cure for 24 hours and then reaming again. I’ve also been doing the same with my wooden pegs only two or three layers scraping after each application. With care I’ve been able to make the bore and pins exact enough to be interchangeable. I start by making my pins 1/4” on the small end and all other dimensions fallow. Looking forward to the rest of your build. HR In the plug inserts- I think it’s not about hardness of the surfaces the pegs engage, but evenness of grain. We’re trying to get the peg shaft to ride against one direction of grain orientation by making the plug with end grain. The wood only needs to be of similar hardness to the peg. I’ve found Maple and Teak to be very good. And I currently use a Japanese hardwood the name of which I can’t remember now, but it’s a lot like teak but not oily. Reamers are weird, they cannot be sharpened by mortals with clunky home shops. Maybe a machinist could sharpen one. You store your reamer wrapped in paper to keep it from touching other tools. It may be chattering because the hickory is too hard. You did use end grain right? I’d switch to maple or something similar if I were you. And be careful what you lie about. If you lie your nose will grow and you’ll be a wooden man. If you continue to lie your wife may kick you in the balls. That’s going to hurt, and it will send you to the hickory dickory doc.
_____________________________
https://www.stephenfaulkguitars.com
|
|
|
REPORT THIS POST AS INAPPROPRIATE |
Date Sep. 11 2020 4:29:27
|
|
New Messages |
No New Messages |
Hot Topic w/ New Messages |
Hot Topic w/o New Messages |
Locked w/ New Messages |
Locked w/o New Messages |
|
Post New Thread
Reply to Message
Post New Poll
Submit Vote
Delete My Own Post
Delete My Own Thread
Rate Posts
|
|
|
Forum Software powered by ASP Playground Advanced Edition 2.0.5
Copyright © 2000 - 2003 ASPPlayground.NET |
0.09375 secs.
|