Welcome to one of the most active flamenco sites on the Internet. Guests can read most posts but if you want to participate click here to register.
This site is dedicated to the memory of Paco de Lucía, Ron Mitchell, Guy Williams, Linda Elvira, Philip John Lee, Craig Eros, Ben Woods, David Serva and Tom Blackshear who went ahead of us.
We receive 12,200 visitors a month from 200 countries and 1.7 million page impressions a year. To advertise on this site please contact us.
Posts: 2802
Joined: Jan. 30 2007
From: London (the South of it), England
damage fret slots
Hello,
I damaged a couple of th eslots in y ebony when hammering in the frets.
I can see a thin top layer of the ebony very slightly lifting up. (chipping (Im sure you know what i mean)
is the fret seated correctly enough to keep those top layers in place for all time? or shuld I removed the frets and try and run some glue under and clamp?
I think this is the right way to go really? just curious as to how i can get the glueunder that little sheet of lifting ebony withour spilling into the fret slot
Are you bevelling the tops of the slots with a triangular file before hammering in the frets? Also, dampening the slot with a drop of water or a bit of white glue rubbed into the slot and levelled off with your finger can help prevent chipping by softening the wood fibres and also acting as a lubricant for the fret tang as it’s being hammered into the slot.
Without seeing pictures and guessing what the problem is, I think it might be best to try to reseat the chips by pushing them down flat with the edge of a metal ruler or the like and drizzling CA glue along the edge to hold them in (along with the fret) without removing the fret. There is the danger of the chips coming off and getting lost if you pull the fret to replace it. I guess the decision to pull it or not would depend on how poorly seated it is.
If you do choose to pull the fret and reseat the chips, it’s helpful to have some Teflon sheeting (or veneer wrapped in scotch tape) the same width as the slots that can be put into the slot and act as a dam against the slot getting flooded with glue during the repair. Once dammed, the loose chips can be reseated and/or any missing wood filled with ebony dust and everything held together with a thin bead of CA. Then pull out the Teflon/veneer dam, sand the board, clean out the slot, bevel its top edges, and refret.
Thanks fur the tips. No I wasn't beveling! I have done now though.
Knew the truck but had totally forgotten.
I've kind destroyed the second fret slot! 😩
I recon I can salvage to a decent level. But annoying. I have removed the fret and managed to glue when some of the chips but a couple of nasty ones remain. Will try again tomorrow. Might have to do super glue and ebony dust.
If they are popping back out after banging them in then the slot is now too loose. put the frets in place and use a hard block on them and clamp them in place. Perhaps use a cowel with clamp in side if its not supported beneath. Then run some super glue into the fret slot and leave it to dry. Should do the trick
Glad you saved the fretboard! That is a relief. I had some bad chipping on a board I removed the frets from. Some just came right out with the heat from a soldering iron and others no so much.
I was told to add a drop of thin super glue to each side of the fret slot. So I thought what’s the harm in a couple extra? Damn glue ran all over my still curing French polish! Set me back a couple sessions after sanding it all out. Ugh.
great thanks Stephen. I will tackle this tonight with those tips in mind. is there a way to increase the tang width? or spread? so the hooks grab the wider ebony slot? (a way without any special tool)
Jason, is that the tip for removing frets more safely? apply heat? cos i think i need to pull a couple.
ha sorry to hear your super glue mishap. another luthiery classic! trying to fix something but breaking something else in the process! I'm doing that regularly
Jason, is that the tip for removing frets more safely? apply heat? cos i think i need to pull a couple.
Hi Stu, heat and moisture helps release the hold any glue in the slot may have on the fret. Also, brushing some water along the sides of the fret helps to reduce chipping as the damp wood will be less brittle/chippy than dry wood. It also seems to lubricate the pull somewhat. I use a soldering iron with a fairly broad tip (maybe 3mm) and heat the fret until I see the water bubble and begin to evaporate, then start pulling it. You don’t need a lot of water, just a thin brushing with a fine artist’s brush will do.
Thanks guys and yes rob that's making sense. Will read back on that when I get round to pulling them.
Yes el burdo! I have a pair summary to that ground flat! I have a smaller pair...I think they are specific fret pullers.
Fretting is almost like a while art of its own. Some of the tools and files and jigs and etc etc etc!! Pages and pages of them on luthier sites
Fret work is like shellack or the ten either critical operations that make the soul of a good guitar. Ive refret a few of my first guitars and learned a lot in the process.
I only use straight fret wire.
I like a fret slot that is not too snug, shouldn't have too pound them in.
I will use some CA as required.
I drive my frets with a nice chamfer on the edge off the slots and wet with boiled linseed oil with a flat plastic no-blow hammer.
_____________________________
I prefer my flamenco guitar spicy, doesn't have to be fast, should have some meat on the bones, can be raw or well done, as long as it doesn't sound like it's turning green on an elevator floor.