Problems bending Indian rosewood sides (Full Version)

Foro Flamenco: http://www.foroflamenco.com/
- Discussions: http://www.foroflamenco.com/default.asp?catApp=0
- - Lutherie: http://www.foroflamenco.com/in_forum.asp?forumid=22
- - - Problems bending Indian rosewood sides: http://www.foroflamenco.com/fb.asp?m=141535



Message

Andy Culpepper -> Problems bending Indian rosewood sides (Jul. 17 2010 23:23:01)

Just curious if anyone has encountered anything like this before..
I'm bending sides with a silicone heating blanket on a form. The last couple of sets have come out with a very noticeable ripple especially in the lower bout, like almost 1 mm between the highest and lowest spots. Here's the best picture I have of it, somewhat mitigated by sanding but I had to live with some ripple so I wouldn't weaken the side too much.
You can see it in the upper right of the picture on the lower bout of the guitar.
So is it just this batch of rosewood perhaps? (from LMI) Anyone else get anything like this ever?



Images are resized automatically to a maximum width of 800px



jshelton5040 -> RE: Problems bending Indian rosewood sides (Jul. 18 2010 14:17:18)

quote:

ORIGINAL: deteresa1

So is it just this batch of rosewood perhaps? (from LMI) Anyone else get anything like this ever?


I've had sides ripple when they were not cured long enough. It may also have something to do with excess moisture when bending. The moisture supposition is due to the fact that I haven't had a ripple since switching to dry bending (I use an iron).



estebanana -> RE: Problems bending Indian rosewood sides (Jul. 18 2010 18:12:30)

D,

It's your bending technique not the wood. You are not letting the rib totally dry on the bending form and it is warping after you remove the rib.

Two things to try. One is to do a second heating with the blanket after the first heating has cooled. You need to cook off all the moisture in the rib before you remove it from the form. The second is to a drill a group of 5/8th holes in the top stainless steel sheet so the moisture can escape. If you do this then put the blanket under the rib instead of on top. The rib will dry in the bender.

If you remove the rib and there is any moisture it will stand a chance to wobble.

Bend once, cook twice.



Andy Culpepper -> RE: Problems bending Indian rosewood sides (Jul. 18 2010 19:24:56)

Interesting.
John, thanks. The wood came in in '07 and was already kiln dried from LMI. Seems like it should have been cured?
I do spray the sides down with a little water, not dripping or even quite wet everywhere.

Stephen, the way I usually bend is, I heat it on the form for about 20-30 mins., then let it cool completely and cook it again for another 10-20. I always have the blanket under the wood. After the first one came out rippled, I tried soaking both sides in "Supersoft", this stuff we had lying around that's supposed to make things bend easier. Then I put them both back on the bender and did my usual routine on both. The one that was still unbent when I put on the Supersoft came out quite a bit better than the first but it still had some ripple (it was the players side luckily). I also recooked the already bent one but it came out unchanged.
I guess in the future I will just give it longer to sit on there....



jshelton5040 -> RE: Problems bending Indian rosewood sides (Jul. 18 2010 19:53:45)

quote:

ORIGINAL: deteresa1

Interesting.
John, thanks. The wood came in in '07 and was already kiln dried from LMI. Seems like it should have been cured?
I do spray the sides down with a little water, not dripping or even quite wet everywhere.


I would consider 07 to be borderline too young to use. I usually try to wait at least 5 years for hardwoods and 3 for soft. Kiln drying is not curing. I know there is some controversy about the effect of kiln drying on wood but if possible I would avoid it. A long slow air dry cure in a humidity controlled environment is best. At least that's the old axiom.



Andy Culpepper -> RE: Problems bending Indian rosewood sides (Jul. 22 2010 21:58:43)

Update:
Another set from the same batch bent perfect...strange.



Page: [1]

Valid CSS!




Forum Software powered by ASP Playground Advanced Edition 2.0.5
Copyright © 2000 - 2003 ASPPlayground.NET