Welcome to one of the most active flamenco sites on the Internet. Guests can read most posts but if you want to participate click here to register.
This site is dedicated to the memory of Paco de Lucía, Ron Mitchell, Guy Williams, Linda Elvira, Philip John Lee, Craig Eros, Ben Woods, David Serva and Tom Blackshear who went ahead of us.
We receive 12,200 visitors a month from 200 countries and 1.7 million page impressions a year. To advertise on this site please contact us.
|
|
Jorge's First Build
|
You are logged in as Guest
|
Users viewing this topic: none
|
|
Login | |
|
constructordeguitarras
Posts: 1676
Joined: Jan. 29 2012
From: Seattle, Washington, USA
|
RE: Jorge's First Build (in reply to El Polaco)
|
|
|
Looks really nice, Jorge. I saw the fret slots on a table saw before attaching the fingerboard, but in your situation I would set a sliding bevel gauge to the correct angle and hold it in position so that the saw can jig against it (or even clamp it in position); also, use a depth stop on the saw, which could be a thin strip of wood clamped to the blade or even several layers of tape (and be sure of the desired relationship between the depth stop and the position or thickness of the bevel gauge). Another way I have of accurately sawing to a line is to first knife the line, then deepen it slightly with the corner of a chisel, then use the edge of the chisel to cut a tiny strip of wood (of triangular cross section) out from a tiny distance away from the line to the bottom of the knife cut in the line. This way you can rest the saw blade against the shoulder created at the line. The kerf will be at one side of the line. I never glue frets in unless I am replacing one where the slot may be enlarged from the barbs on the tang of the old one. I hammer them in with a plastic hammer to avoid denting them. With regard to finishing--especially if you are using French polish: Sand thoroughly, preferably in daylight. It wouldn't hurt to dampen slightly, let dry, and then sand again with 220 and then 320 grit. There will very likely be things that you can't see before finishing that will show up during finishing, and you can fill them in with finish then, but it will be less work to sand thoroughly before hand.
_____________________________
Ethan Deutsch www.edluthier.com www.facebook.com/ethandeutschguitars www.youtube.com/marioamayaflamenco I always have flamenco guitars available for sale.
|
|
|
REPORT THIS POST AS INAPPROPRIATE |
Date Jun. 15 2012 21:08:28
|
|
constructordeguitarras
Posts: 1676
Joined: Jan. 29 2012
From: Seattle, Washington, USA
|
RE: Jorge's First Build (in reply to TANúñez)
|
|
|
Yes, really. When I dome the soundboard, I don't round the fan braces to fit the doming, either. I think it is rare for anyone to do that, but a few people do. But anyone who has used bent lamination in furnituremaking knows that if you bend flexible pieces and glue them together at the same time you get a very strong result. Moreover, when I glue the bridge on I don't use clamps through the soundhole; I use clamps on the wings only, outside the box, and let the doming apply pressure in the middle--traditionally this was done with rope and wedges. From the early Ramirez III workshop (from "Things About The Guitar," by Jose R., III):
Images are resized automatically to a maximum width of 800px
Attachment (1)
_____________________________
Ethan Deutsch www.edluthier.com www.facebook.com/ethandeutschguitars www.youtube.com/marioamayaflamenco I always have flamenco guitars available for sale.
|
|
|
REPORT THIS POST AS INAPPROPRIATE |
Date Jun. 19 2012 23:25:54
|
|
New Messages |
No New Messages |
Hot Topic w/ New Messages |
Hot Topic w/o New Messages |
Locked w/ New Messages |
Locked w/o New Messages |
|
Post New Thread
Reply to Message
Post New Poll
Submit Vote
Delete My Own Post
Delete My Own Thread
Rate Posts
|
|
|
Forum Software powered by ASP Playground Advanced Edition 2.0.5
Copyright © 2000 - 2003 ASPPlayground.NET |
0.078125 secs.
|